tebl/Composite-Video-Amplifier

Stars
12
Rank 1,597,372 (Top 32 %)
Language
License
GNU General Publi...
Created almost 6 years ago
Updated almost 4 years ago

tebl/Composite-Video-Amplifier

tebl

There are no reviews yet. Be the first to send feedback to the community and the maintainers!

Used for composite modding Atari console systems such as the Atari 2600

RC6502-Apple-1-Replica

An expandable SBC-version of the Apple 1 computer, easy to get started with and lot of cool stuff that can be added to it!

BE6502-Build-a-65c02-computer

A PCB being made while watching Ben Eaters "Build a 6502 computer" video series. Includes the computer itself, a standalone slow clock and an Arduino Mega shield for the bus monitor sketch..

C64-Pi1541-II

I wanted a Pi1541 module that did not feel like I was handling bare electronics, so I made one that hides most of the scary bits (no 3d-printer required).

C64-Modulator-Replacement

A simple modulator replacement for Commodore 64s with "longboards", complements my Lumafix version as well adding an audio connector for second SID.

C64-BlinkenDiag

A version of the DIAG64cart, this mainly changes components for the ones I've already got and adds a lot of LEDs. It's a blinkenlight project for diagnostic usage.

C64-Lumafix

An easier to solder version of the Lumafix board, components spaced out a bit more to make things easier on the beginner (mostly meaning me). Can also be used to bypass noisy signals on motherboard, wireing directly to modulator replacement.

BulkyMIDI-32

A HW build of the MT32-PI project, allowing you to emulate a Roland MT-32 using a Raspberry Pi. Includes enough additional modules to build a MIDI-mountain as well as adapters for connecting to most things retro.

C64-Power-Saver

C64 power supplies are ancient, they go bad every day so use protection!

C64-Pi1541-Module

I wanted an alternative to the SD2IEC on my Commodore 64, and I almost instantly took a liking to Pi1541 software. I did however need to design a board for it and this was the end result - even includes beepers, OLEDs and two IEC connectors

C64-XUM1541-II

An updated version of my C64 XUM1541, this supports the newer XUM1541 firmware and comes with a few extra goodies.

C64-XUM1541

Simple PCB for building a XUM1541, a device for copying data to and from Commodore 1541 disk drives using a modern computer.

Amiga-DrawBridge

A PCB build of Rob Smiths Amiga DrawBridge, an Arduino-based solution for reading and writing Amiga floppy disks on modern hardware. Also includes version of Greaseweazle.

RC1802-Cosmac-ELF

With the RC6502-project for making an Apple 1 replica done I wanted to do something different, so I started designing a simple version of the RCA 1802-based Cosmac ELF instead.

C64-Kernal-Switcher

Switchless kernal switcher for the common breadbin Commodore 64, "longboards". Reuses power LED for easier use.

C64-CPM-Cartridge

A recreation of the CP/M cartridge for the Commodore 64.

8BIT-Wave

An Arduino-based tape player for old school computers like the ZX Spectrum, Dragon 32 etc. Hardware is compatible with tzxduino/arduitape and Maxduino firmware.

ZX-Interface-2.021

An old-school remake of the ZX Interface 2 with some modern tweaks - mainly by integrating bank switching into the interface itself. Everything done with basic logic chips and components, no magic black boxes in sight.

RC-ONE

A recreation of the MOS KIM-1 microcomputer, the start of the Commodore-line of computers. Complete with hex keypad, six digit displays and a lot of 8-bit fun!

C64-JoyKEY

WASD-style joystick for vintage computers. With an added Arduino Pro Micro you can use it as a USB-keyboard, so if you wanted a DIY streamdeck or Macro-keyboard - then the C64 JoyKEY can do that as well.

C64-Stereo-SID

There are many Stereo SID boards, but this one in mine... Add a second SID of the same type or newer substitutes for adding stereo audio to your system...

C64-Joystick-Switcher

Wanted a joystick switcher for my Commodore 64, so I built one by adapting C64 Mega Switcher for use with Atari-style joysticks. Supports secondary fire-button when using Sega Master System gamepads, even includes an auto-fire circuit.

C64-Mega-Switcher

Adapter for using Sega Mega Drive/Genesis controllers on a C64, with builtin port switcher so no more cable switching!

Apple2-Prototyping-Card

Prototyping card for developing new hardware for legacy Apple ][, //e and //gs computers.

C64-Joystick-Adapter

A simple device that allows the connection of two Commodore 64 joysticks to a modern computer over USB (using an Arduino Pro Micro). The overall goal is to be able to use vintage joysticks with emulators.

C64-PlayOnTape

It's a tapuino, mostly because I wanted to build one. Uses an Arduino to load tapes on the good old Commodore 64.

RC2014

RC2014 expansion modules and scripts

retropie-dosbox-configure

Simple bash scripts that can be used to configure DOSBox games on RetroPie

A7800-Mega-Adapter

Adapter for using a wired Sega Mega Drive/Genesis controller on an Atari 7800.

Atari-Joystick-Tester

Simple joystick tester, can be used with the common Atari 9-pin joysticks and paddles (tested using multimeter).

MSX-Mega-Adapter

Adapter so that Sega Mega Drive (Sega Genesis in North America) gamepads can safely be used with the MSX line of computers.

C64-IRQ-LED

Changes Commodore 64 power LED so that it is green when I/O is used on system, reverts to red when done.

Apple2-Joystick-Adapter

Adapter that plugs into the Game I/O connector on the Apple //e motherboard to add support for Atari-style joysticks, cables can be routed to the back of the case for easy access.

breadboard

Created a simple PCB that can be used to transfer breadboard contents more directly to a PCB.

Amiga-Mouse-Switch

An attempt at building an automatic Amiga Mouse/Joystick switch (when used with Amiga port 1) - pushing the button changes the device connected. No more two-cable Merengue for me on the Amiga 500, forever more!

D32-Joystick-Adapter

Joystick adapter so that Atari-style joysticks can be used on the Dragon 32/64 and Radioshack CoCo line of computers.

RetroPanel

The missing piece for everyone who has a functional AT-system, but only ATX-cases. This adds a turbo-switch, a smart power switch and that highly desired Mhz-display (also a clock, because why not).

NoiseMaker

Compact Flash, SD-cards and Gotek drives take the anger out of retro-computing, but at the cost of an oddly silent computer. This is an Arduino project to solve that in a way that should be easy for anyone to assemble.

RC6802-Microchicken

Computer based on the Motorola 6802 processor, called RC6802 Microchicken as it's an adaption of the one found in a computer projects book by Daniel Metzger.

CPC464-Joystick-Splitter

A simple joystick splitter for use with the Amstrad CPC 464 computer. This allows the use of two Atari-style joysticks on the computer, but note that as the computer does not have power on the connector - this will not work with joysticks that have autofire.

tebl

Profile repository

A2600-Keyboard

A new version of the classic Atari 2600 Keyboard controller, mostly because I wanted the overlays without paying for worn cardboard sheets.

RetroShield1802-PCB

Arduino Mega 2560 shield adding secondary 1802 processor to run the latest 1802-based software (most may be from the 70s).

VU-Switch

Building an audio input switcher, four 3.5mm audio inputs and one 3.5mm audio output for connecting to my 80s Boombox. VU-meters added, because they're cool!

Acorn-Joystick-Adapter

Joystick adapter that allows you to use common Atari-style joysticks (C64/Amiga/Atari) on your BBC Micro computer!

Christmas-2020

A simple and quite fun Arduino-project for Christmas 2020 (it's a blinking tree).

RC-Project-Board

Playing around with an Arduino and a breadboard is a lot of fun, but I wanted to include my retro-computer builds so I made the project boards to make this a lot easier (for me). Also includes a few projects, some of them in the form of PCBs as well!