sdr-enthusiasts/docker-readsb-protobuf

Mictronics' readsb-protobuf Mode-S/ADSB/TIS decoder for RTLSDR, BladeRF, Modes-Beast and GNS5894 devices, running in a docker container.

This version uses Google's protocol buffer for data storage and exchange with web application. Saves on storage space and bandwidth.

This container also contains InfluxData's Telegraf, and can send flight data and readsb metrics to InfluxDB (if wanted - not started by default).

Support for all supported SDRs is compiled in. Builds and runs on x86_64, arm32v7 and arm64v8 (see below).

This image will configure a software-defined radio (SDR) to receive and decode Mode-S/ADSB/TIS data from aircraft within range, for use with other services such as:

• sdr-enthusiasts/docker-adsbexchange to feed ADSB data to adsbexchange.com
• sdr-enthusiasts/docker-adsbhub to feed ADSB data into adsbhub.org
• sdr-enthusiasts/docker-piaware to feed ADSB data into flightaware.com
• sdr-enthusiasts/docker-flightradar24 to feed ADSB data into flightradar24.com
• sdr-enthusiasts/docker-radarbox to feed ADSB data into radarbox.com
• sdr-enthusiasts/docker-opensky-network to feed ADSB data into opensky-network.org
• sdr-enthusiasts/docker-planefinder to feed ADSB data into planefinder.net
• mikenye/adsb-to-influxdb to feed data into your own instance of InfluxDB, for visualisation with Grafana and/or other tools
• Any other tools that can receive Beast, BeastReduce, Basestation or the raw data feed from readsb or dump1090 and their variants

bladeRF & plutoSDR are untested - I don't own bladeRF or plutoSDR hardware (only RTL2832U as outlined above), but support for the devices is compiled in. If you have the hardware and would be willing to test, please open an issue on GitHub.

Note for Users running 32-bit Debian Buster-based OSes on ARM

Please see: Buster-Docker-Fixes!

Table of Contents

• sdr-enthusiasts/docker-readsb-protobuf
  • Note for Users running 32-bit Debian Buster-based OSes on ARM
  • Table of Contents
  • Supported tags and respective Dockerfiles
  • Multi Architecture Support
  • Prerequisites
  • Identifying your SDR's device path
  • Up-and-Running with docker run
  • Up-and-Running with Docker Compose
  • Testing the container
  • Environment Variables
    • Container Options
    • readsb General Options
    • readsb Network Options
      • READSB_NET_CONNECTOR syntax
    • readsb RTL-SDR Options
    • readsb BladeRF Options
    • readsb Mode-S Beast Options
    • readsb GNS HULC Options
    • readsb ADALM-Pluto SDR Options
    • readsb Graphs Options
    • Auto-Gain Options
    • InfluxDB Options
    • Prometheus Options
  • Ports
  • Paths & Volumes
  • Auto-Gain system
    • Initialisation Stage
    • Fine-Tuning Stage
    • Finished Stage
    • State/Log/Stats Files
    • Forcing auto-gain to re-run from scratch
  • Advanced Usage: Creating an MLAT Hub
  • PlutoSDR Support
  • Grafana Dashboard
  • InfluxDB Schema
    • aircraft Measurement
    • autogain Measurement
    • polar_range Measurement
    • readsb Measurement
  • Estimating PPM
  • Getting help
  • Changelog

Supported tags and respective Dockerfiles

• latest should always contain the latest released versions of rtl-sdr, bladeRF, libiio, libad9361-iio and readsb. This image is built nightly from the main branch Dockerfile for all supported architectures.
• latest_nohealthcheck is the same as the latest version above. However, this version has the docker healthcheck removed. This is done for people running platforms (such as Nomad) that don't support manually disabling healthchecks, where healthchecks are not wanted.
• Specific version and architecture tags are available if required, however these are not regularly updated. It is generally recommended to run latest.

Multi Architecture Support

Currently, this image should pull and run on the following architectures:

• amd64: Linux x86-64
• arm32v7, armv7l: ARMv7 32-bit (Odroid HC1/HC2/XU4, RPi 2/3)
• arm64v8, aarch64: ARMv8 64-bit (RPi 3B+/4)

Prerequisites

Kernel Module Configuration

NOTE: If you used the docker-install.sh script, you can skip this section.

Before we can plug in our RTL-SDR dongle, we need to blacklist the kernel modules for the RTL-SDR USB device from being loaded into the host's kernel and taking ownership of the device.

There are three parts to this.

1. Blacklist modules from being directly loaded AND blacklist modules from being loaded as a dependency of other modules
2. Unload any of our blacklisted modules from memory
3. Updating the initramfs boot image to remove any references to our now blacklisted modules

1. Blacklist Modules

To do this, we will create a blacklist file at /etc/modprobe.d/blacklist-rtlsdr.conf with the following command. While logged in as root, please copy and paste all lines at once, and press enter after to ensure the final line is given allowing it to run.

sudo tee /etc/modprobe.d/blacklist-rtlsdr.conf <<TEXT1
# Blacklist host from loading modules for RTL-SDRs to ensure they
# are left available for the Docker guest.

blacklist dvb_core
blacklist dvb_usb_rtl2832u
blacklist dvb_usb_rtl28xxu
blacklist dvb_usb_v2
blacklist r820t
blacklist rtl2830
blacklist rtl2832
blacklist rtl2832_sdr
blacklist rtl2838
blacklist rtl8192cu
blacklist rtl8xxxu

# This alone will not prevent a module being loaded if it is a
# required or an optional dependency of another module. Some kernel
# modules will attempt to load optional modules on demand, which we
# mitigate here by causing /bin/false to be run instead of the module.
#
# The next time the loading of the module is attempted, the /bin/false
# will be executed instead. This will prevent the module from being
# loaded on-demand. Source: https://access.redhat.com/solutions/41278

install dvb_core /bin/false
install dvb_usb_rtl2832u /bin/false
install dvb_usb_rtl28xxu /bin/false
install dvb_usb_v2 /bin/false
install r820t /bin/false
install rtl2830 /bin/false
install rtl2832 /bin/false
install rtl2832_sdr /bin/false
install rtl2838 /bin/false
install rtl8192cu /bin/false
install rtl8xxxu /bin/false

TEXT1

2. Unload Modules

Next, ensure the modules are unloaded by running the following commands:

sudo modprobe -r rtl2832_sdr
sudo modprobe -r dvb_usb_rtl2832u
sudo modprobe -r dvb_usb_rtl28xxu
sudo modprobe -r dvb_usb_v2
sudo modprobe -r r820t
sudo modprobe -r rtl2830
sudo modprobe -r rtl2832
sudo modprobe -r rtl2838
sudo modprobe -r rtl8192cu
sudo modprobe -r rtl8xxxu
sudo modprobe -r dvb_core

3. Update the Boot Image

Now we need to update our boot image to ensure any references to the modules we've blacklisted are removed

sudo update-initramfs -u

This will take a minute or more depending on the speed of your system, and output lots of status message lines as it goes until it is finished.

Failure to do the steps above will result in the error below being spammed to the readsb container log.

usb_claim_interface error -6
rtlsdr: error opening the RTLSDR device: Device or resource busy

Identifying your SDR's device path

Plug in your USB radio, and run the command lsusb. Find your radio. It'll look something like this:

Bus 001 Device 004: ID 0bda:2832 Realtek Semiconductor Corp. RTL2832U DVB-T

Take note of the USB bus number, and USB device number. In the output above, its 001 and 004 respectively. While the individual device can be passed through (/dev/bus/usb/001/004 in this case), it's more reliable to pass the entire USB bus through, as seen in the examples below.

Up-and-Running with docker run

Start the docker container, passing through the USB device:

docker volume create readsbpb_rrd
docker volume create readsbpb_autogain
docker run \
 -d \
 -it \
 --restart=always \
 --name readsb \
 --hostname readsb \
 --device /dev/bus/usb:/dev/bus/usb \
 -p 8080:8080 \
 -p 30005:30005 \
 -e TZ=<YOUR_TIMEZONE> \
 -e READSB_DCFILTER=true \
 -e READSB_DEVICE_TYPE=rtlsdr \
 -e READSB_FIX=true \
 -e READSB_GAIN=autogain \
 -e READSB_LAT=<YOUR_LATITUDE> \
 -e READSB_LON=<YOUR_LONGITUDE> \
 -e READSB_MODEAC=true \
 -e READSB_RX_LOCATION_ACCURACY=2 \
 -e READSB_STATS_RANGE=true \
 -e READSB_NET_ENABLE=true \
 -v readsbpb_autogain:/run/autogain \
 -v readsbpb_rrd:/run/collectd \
 --tmpfs=/run:exec,size=64M \
 --tmpfs=/var/log:size=32M \
 ghcr.io/sdr-enthusiasts/docker-readsb-protobuf:latest

For example:

docker volume create readsbpb_rrd
docker volume create readsbpb_autogain
docker run \
 -d \
 -it \
 --restart=always \
 --name readsb \
 --hostname readsb \
 --device /dev/bus/usb:/dev/bus/usb \
 -p 8080:8080 \
 -p 30005:30005 \
 -e TZ=Australia/Perth \
 -e READSB_DCFILTER=true \
 -e READSB_DEVICE_TYPE=rtlsdr \
 -e READSB_FIX=true \
 -e READSB_GAIN=autogain \
 -e READSB_LAT=33.33333 \
 -e READSB_LON=-111.11111 \
 -e READSB_MODEAC=true \
 -e READSB_RX_LOCATION_ACCURACY=2 \
 -e READSB_STATS_RANGE=true \
 -e READSB_NET_ENABLE=true \
 -v readsbpb_autogain:/run/autogain \
 -v readsbpb_rrd:/run/collectd \
 --tmpfs=/run:exec,size=64M \
 --tmpfs=/var/log:size=32M \
 ghcr.io/sdr-enthusiasts/docker-readsb-protobuf:latest

Alternatively, you could pass through the entire USB bus with --device /dev/bus/usb:/dev/bus/usb, but please understand the security implications of doing so.

Up-and-Running with Docker Compose

An example docker-compose.yml file is below:

version: '2.0'

volumes:
  readsbpb_rrd:
  readsbpb_autogain:

services:

  readsb:
    image: ghcr.io/sdr-enthusiasts/docker-readsb-protobuf:latest
    tty: true
    container_name: readsb
    hostname: readsb
    restart: always
    devices:
      - /dev/bus/usb:/dev/bus/usb
    ports:
      - 8080:8080
      - 30005:30005
    environment:
      - TZ=Australia/Perth
      - READSB_DCFILTER=true
      - READSB_DEVICE_TYPE=rtlsdr
      - READSB_FIX=true
      - READSB_GAIN=autogain
      - READSB_LAT=-33.33333
      - READSB_LON=111.11111
      - READSB_MODEAC=true
      - READSB_RX_LOCATION_ACCURACY=2
      - READSB_STATS_RANGE=true
      - READSB_NET_ENABLE=true
    volumes:
      - readsbpb_rrd:/run/collectd
      - readsbpb_autogain:/run/autogain
      - /proc/diskstats:/proc/diskstats:ro
    tmpfs:
      - /run/readsb:size=64M
      - /var/log:size=32M

Testing the container

Once running, you can test the container to ensure it is correctly receiving & decoding ADSB traffic by issuing the command:

docker exec -it readsb viewadsb

Which should display a departure-lounge-style screen showing all the aircraft being tracked, for example:

 Hex    Mode  Sqwk  Flight   Alt    Spd  Hdg    Lat      Long   RSSI  Msgs  Ti -
────────────────────────────────────────────────────────────────────────────────
 7C801C S                     8450  256  296                   -28.0    14  1
 7C8148 S                     3900                             -21.5    19  0
 7C7A48 S     1331  VOZ471   28050  468  063  -31.290  117.480 -26.8    48  0
 7C7A4D S     3273  VOZ694   13100  376  077                   -29.1    14  1
 7C7A6E S     4342  YGW       1625  109  175  -32.023  115.853  -5.9    71  0
 7C7A71 S           YGZ        725   64  167  -32.102  115.852 -27.1    26  0
 7C42D1 S                    32000  347  211                   -32.0     4  1
 7C42D5 S                    33000  421  081  -30.955  118.568 -28.7    15  0
 7C42D9 S     4245  NWK1643   1675  173  282  -32.043  115.961 -13.6    60  0
 7C431A S     3617  JTE981   24000  289  012                   -26.7    41  0
 7C1B2D S     3711  VOZ9242  11900  294  209  -31.691  116.118  -9.5    65  0
 7C5343 S           QQD      20000  236  055  -30.633  116.834 -25.5    27  0
 7C6C96 S     1347  JST116   24000  397  354  -30.916  115.873 -17.5    62  0
 7C6C99 S     3253  JST975    2650  210  046  -31.868  115.993  -2.5    70  0
 76CD03 S     1522  SIA214     grnd   0                        -22.5     7  0
 7C4513 S     4220  QJE1808   3925  282  279  -31.851  115.887  -1.9    35  0
 7C4530 S     4003  NYA      21925  229  200  -30.933  116.640 -19.8    58  0
 7C7533 S     3236  XFP       4300  224  266  -32.066  116.124  -6.9    74  0
 7C4D44 S     3730  PJQ      20050  231  199  -31.352  116.466 -20.1    62  0
 7C0559 S     3000  BCB       1000                             -18.4    28  0
 7C0DAA S     1200            2500  146  002  -32.315  115.918 -26.6    48  0
 7C6DD7 S     1025  QFA793   17800  339  199  -31.385  116.306  -8.7    53  0
 8A06F0 S     4131  AWQ544    6125  280  217  -32.182  116.143 -12.6    61  0
 7CF7C4 S           PHRX1A                                     -13.7     8  1
 7CF7C5 S           PHRX1B                                     -13.3     9  1
 7C77F6 S           QFA595     grnd 112  014                   -33.2     2  2

Press CTRL-C to escape this screen.

You should also be able to point your web browser at http://dockerhost:8080/ to view the web interface.

Environment Variables

Container Options

readsb General Options

Where the default value is "Unset", readsb's default will be used.

readsb Network Options

Where the default value is "Unset", readsb's default will be used.

READSB_NET_CONNECTOR syntax

This variable allows you to configure outgoing connections. The variable takes a semicolon (;) separated list of ip,port,protocol, where:

• ip is an IP address. Specify an IP/hostname/containername for outgoing connections.
• port is a TCP port number
• protocol can be one of the following:
  • beast_out: Beast-format output
  • beast_in: Beast-format input
  • raw_out: Raw output
  • raw_in: Raw input
  • sbs_out: SBS-format output
  • vrs_out: VRS-format JSON output

For example, to pull in MLAT results (so the performance graphs in the web interface show MLAT numbers), you could do the following:

    environment:
    ...
      - READSB_NET_CONNECTOR=piaware,30105,beast_in;adsbx,30105,beast_in;rbfeeder,30105,beast_in
    ...

readsb RTL-SDR Options

Use with READSB_DEVICE_TYPE=rtlsdr.

Where the default value is "Unset", readsb's default will be used.

readsb BladeRF Options

Use with READSB_DEVICE_TYPE=bladerf.

Where the default value is "Unset", readsb's default will be used.

readsb Mode-S Beast Options

Use with READSB_DEVICE_TYPE=modesbeast.

Where the default value is "Unset", readsb's default will be used.

Beast binary protocol and hardware handshake are always enabled.

readsb GNS HULC Options

Use with READSB_DEVICE_TYPE=gnshulc.

readsb ADALM-Pluto SDR Options

Use with READSB_DEVICE_TYPE=plutosdr.

Where the default value is "Unset", readsb's default will be used.

readsb Graphs Options

Where the default value is "Unset", readsb's default will be used.

Auto-Gain Options

These variables control the auto-gain system (explained further below). These should rarely need changing from the defaults.

InfluxDB Options

These variables control the sending of flight data and readsb metrics to InfluxDB (via a built-in instance of Telegraf).

Prometheus Options

These variables control exposing flight data and readsb metrics to Prometheus (via a built-in instance of Telegraf).

Ports

In addition to the ports listed above, depending on your readsb configuration the container may also be listening on other ports that you'll need to map through (if external connectivity is required).

Some common ports are as follows (which may or may not be in use depending on your configuration):

Paths & Volumes

Auto-Gain system

An automatic gain adjustment system is included in this container, and can be activated by setting the environment variable READSB_GAIN to autogain. You should also map /run/autogain to persistant storage, otherwise the auto-gain system will start over each time the container is restarted.

Why is this written in bash? Because I wanted to keep the container size down and not have to install an interpreter like python. I don't know C/Go/Perl or any other languages.

Auto-gain will take several weeks to initially (over the period of a week or so) work out feasible maximum and minimum gain levels for your environment. It will then perform a fine-tune process to find the optimal gain level.

During each process, gain levels are ranked as follows:

• The range achievable by each gain level
• The signal-to-noise ratio of the receiver

The ranking process is done by sorting the gain levels for each statistic from worst to best, then awarding points. 0 points are awarded for the worst gain level, 1 point for the next gain level all the way up to several points for the best gain level (total number of points is the number of gain levels tested). The number of points for each gain level is totalled, and the optimal gain level is the level with the largest number of points. Any gain level with a percentage of "strong signals" outside of AUTOGAIN_PERCENT_STRONG_MESSAGES_MAX and AUTOGAIN_PERCENT_STRONG_MESSAGES_MIN is discarded.

Using this method, auto-gain tried to achieve the best balance of range, tracks and signal-to-noise ratio, whilst ensuring an appropriate number of "strong signals".

The auto-gain system will work as follows:

Initialisation Stage

In the initialisation process:

1. readsb is set to maximum gain (AUTOGAIN_MAX_GAIN_VALUE).
2. Results are collected up to AUTOGAIN_INITIAL_PERIOD (up to 2 hours by default).
3. Check to ensure at least AUTOGAIN_INITIAL_MSGS_ACCEPTED messages have been locally accepted (1,000,000 by default). If not, continue collecting data for up to 24 hours. This combination of time and number of messages ensures we have enough data to make a valid initial assessment of each gain level.
4. Gain level is lowered by one level.
5. Gain levels are reviewed from lowest to highest gain level. If there have been gain levels resulting in a percentage of strong messages between AUTOGAIN_PERCENT_STRONG_MESSAGES_MAX and AUTOGAIN_PERCENT_STRONG_MESSAGES_MIN, and there have been three consecutive gain levels above AUTOGAIN_PERCENT_STRONG_MESSAGES_MAX, auto-gain lowers the maximum gain level.
6. Gain levels are reviewed from highest to lowest gain level. If there have been gain levels resulting in a percentage of strong messages between AUTOGAIN_PERCENT_STRONG_MESSAGES_MAX and AUTOGAIN_PERCENT_STRONG_MESSAGES_MIN, and there have been three consecutive gain levels below AUTOGAIN_PERCENT_STRONG_MESSAGES_MIN, auto-gain discontinues testing gain levels.

Auto-gain then moves onto the fine-tuning stage.

Fine-Tuning Stage

In the fine-tuning process:

1. readsb is set to maximum gain level chosen at the end of the initialisation process.
2. Results are collected up to AUTOGAIN_FINETUNE_PERIOD (7 days by default).
3. Check to ensure at least AUTOGAIN_FINETUNE_MSGS_ACCEPTED messages have been locally accepted (7,000,000 by default). If not, continue collecting data for up to 48 hours. This combination of time and number of messages ensures we have enough data to make an accurate assessment of each gain level, and by using 7 days this ensures any peaks/troughs in data due to quiet/busy days of the week do not skew results.
4. Gain level is lowered by one level until the minimum gain level chosen at the end of the initialisation process is reached.

At this point, all of the tested gain levels are ranked based on the criterea discussed above.

The gain level with the most points is chosen, and readsb is set to this gain level.

Auto-gain then moves onto the finished stage.

Finished Stage

In the finished stage, auto-gain does nothing (as readsb is operating at optimal gain) for AUTOGAIN_FINISHED_PERIOD (1 year by default). After this time, auto-gain reverts to the initialisation stage and the entire process is completed again. This makes sure your configuration is always running at the optimal gain level as your RTLSDR ages.

State/Log/Stats Files

All files for auto-gain are located at /run/autogain within the container. They should not be modified by hand.

Forcing auto-gain to re-run from scratch

Run docker exec <container_name> rm /run/autogain/* to remove all existing auto-gain state data. Restart the container and auto-gain will detect this and re-start at initialisation stage.

Advanced Usage: Creating an MLAT Hub

There may be reasons you wish to use readsb to combine MLAT feeds from different collectors, to feed into visualisation tools (eg: mikenye/tar1090) or data collectors (eg: mikenye/adsb-to-influxdb).

To do this, you can create a second container to act as an MLAT hub.

Here are example service definitions (from a docker-compose.yml file) for readsb, mlathub, adsb2influxdb and tar1090.

...
  readsb:
    image: ghcr.io/sdr-enthusiasts/docker-readsb-protobuf:latest
    tty: true
    container_name: readsb
    hostname: readsb
    restart: always
    devices:
      - /dev/bus/usb:/dev/bus/usb
    ports:
      - 8079:8080
      - 30003:30003
      - 30005:30005
    networks:
      - adsbnet
    environment:
      - TZ=Australia/Perth
      - READSB_DCFILTER=true
      - READSB_DEVICE_TYPE=rtlsdr
      - READSB_FIX=true
      - READSB_GAIN=autogain
      - READSB_LAT=-33.33333
      - READSB_LON=111.11111
      - READSB_MAX_RANGE=600
      - READSB_MODEAC=true
      - READSB_RX_LOCATION_ACCURACY=2
      - READSB_STATS_RANGE=true
      - READSB_NET_ENABLE=true
      - READSB_NET_CONNECTOR=mlathub,30105,beast_in
    volumes:
      - readsbpb_rrd:/run/collectd
      - readsbpb_autogain:/run/autogain
    tmpfs:
      - /run/readsb:size=64M
      - /var/log:size=32M

  mlathub:
    image: ghcr.io/sdr-enthusiasts/docker-readsb-protobuf:latest
    tty: true
    container_name: mlathub
    hostname: mlathub
    restart: always
    ports:
      - 30105:30105
    networks:
      - adsbnet
    environment:
      - TZ=Australia/Perth
      - DISABLE_PERFORMANCE_GRAPHS=true
      - DISABLE_WEBAPP=true
      - READSB_NET_ENABLE=true
      - READSB_NET_ONLY=true
      - READSB_FORWARD_MLAT=true
      - READSB_NET_CONNECTOR=piaware,30105,beast_in;adsbx,30105,beast_in;rbfeeder,30105,beast_in
      - READSB_NET_BEAST_OUTPUT_PORT=30105

  adsb2influxdb:
    image: mikenye/adsb-to-influxdb:latest
    tty: true
    container_name: adsb2influxdb
    restart: always
    environment:
      - TZ=Australia/Perth
      - INFLUXDBURL=http://influxdb:8086
      - ADSBHOST=readsb
      - MLATHOST=mlathub
    networks:
      - adsbnet

  tar1090:
    image: mikenye/tar1090:latest
    tty: true
    container_name: tar1090
    restart: always
    depends_on:
      - readsb
    environment:
      - TZ=Australia/Perth
      - BEASTHOST=readsb
      - MLATHOST=mlathub
      - LAT=-33.33333
      - LONG=111.11111
    volumes:
      - "tar1090_heatmap:/var/globe_history"
    tmpfs:
      - /run:exec,size=64M
      - /var/log:size=32M
    networks:
      - adsbnet
    ports:
      - 8078:80

In this example:

• readsb reads and demodulates the ADSB data from the RTLSDR.
• Other services (such as adsbx, piaware and rbfeeder - not shown) pull ADSB data from readsb, perform multilateration, and have their resulting MLAT data published on TCP port 30105.
• mlathub connects to the services providing MLAT results (via READSB_NET_CONNECTOR), and combines them into a single feed, available on TCP port 30105 (via READSB_NET_BEAST_OUTPUT_PORT=30105).
• readsb pulls these MLAT results (via a READSB_NET_CONNECTOR) so MLAT results show up in its webapp. It is important to note that MLAT results are NOT fed to feeders, which is the desired approach.
• adsb2influxdb pulls these MLAT results (via MLATHOST) so MLAT metrics are sent to InfluxDB.
• tar1090 pulls these MLAT results (via MLATHOST) so MLAT positions show up in tar1090's web interface.

You must make absolutely certain that READSB_FORWARD_MLAT is NOT set on your main readsb instance! This is why we perform the MLAT hub functionality in a separate instance of readsb. You do not want to cross-contaminate MLAT results between feeders. Doing so will almost certainly result in your MLAT results being rejected, and/or may end up getting you ignored/banned from feeding services.

PlutoSDR Support

If using PlutoSDR, you will need to configure a host entry for pluto.local.

If using docker run, you can add the command line argument --add-host pluto.local:<IP_OF_PLUTO_HOST>.

If using docker compose, you can add the following to the readsb: service definition:

    extra_hosts:
      - "pluto.local:<IP_OF_PLUTO_HOST>"

Replace <IP_OF_PLUTO_HOST> with the IP address of your PlutoSDR host.

Grafana Dashboard

If you're using INFLUXDBURL and pushing metrics into InfluxDB, I've put together an example Grafana dashboard, which can be found here:

https://grafana.com/grafana/dashboards/13168

InfluxDB Schema

If INFLUXDBURL is set, an instance of Telegraf will be started within the container, and metrics will be written to the InfluxDB.

The database readsb will be created if it does not exist.

Within this database are the following measurements:

aircraft Measurement

Tags and fields used for this measurement should match Virtual Radar Server's JSON response ("the new way").

autogain Measurement

polar_range Measurement

readsb Measurement

Field keys should be as-per the StatisticEntry message schema from readsb.proto.

Estimating PPM

Every RTL-SDR dongle will have a small frequency error as it is cheaply mass produced and not tested for accuracy. This frequency error is linear across the spectrum, and can be adjusted in most SDR programs by entering a PPM (parts per million) offset value. This image allows you to adjust the PPM figure using the READSB_RTLSDR_PPM environment variable.

To estimate your RTL-SDR's PPM, you can:

• Stop the readsb container if it is running (freeing up the RTL-SDR for use)
• Running docker run --rm -it --entrypoint /scripts/estimate_rtlsdr_ppm.sh --device /dev/bus/usb ghcr.io/sdr-enthusiasts/docker-readsb-protobuf:latest. This takes about 30 minutes.
• Updating your readsb container with the suggested PPM value

Example output is as follows:

$ docker run --rm -it --entrypoint /scripts/estimate_rtlsdr_ppm.sh --device /dev/bus/usb ghcr.io/sdr-enthusiasts/docker-readsb-protobuf:latest

Running rtl_test -p for 30 minutes

Found 1 device(s):
  0:  Realtek, RTL2832U, SN: 00001000

Using device 0: Generic RTL2832U
Found Rafael Micro R820T tuner
Supported gain values (29): 0.0 0.9 1.4 2.7 3.7 7.7 8.7 12.5 14.4 15.7 16.6 19.7 20.7 22.9 25.4 28.0 29.7 32.8 33.8 36.4 37.2 38.6 40.2 42.1 43.4 43.9 44.5 48.0 49.6
[R82XX] PLL not locked!
Sampling at 2048000 S/s.
Reporting PPM error measurement every 10 seconds...
Press ^C after a few minutes.
Reading samples in async mode...
real sample rate: 2048129 current PPM: 63 cumulative PPM: 63
real sample rate: 2047957 current PPM: -21 cumulative PPM: 20
real sample rate: 2048125 current PPM: 61 cumulative PPM: 34
...<lines removed for brevity>...
real sample rate: 2047998 current PPM: -1 cumulative PPM: 1
real sample rate: 2047992 current PPM: -3 cumulative PPM: 0
real sample rate: 2048005 current PPM: 3 cumulative PPM: 1
Signal caught, exiting!

User cancel, exiting...
Samples per million lost (minimum): 0

Results:

PPM setting of: -2, Score of: 1
PPM setting of: 10, Score of: 1
PPM setting of: 20, Score of: 1
PPM setting of: 34, Score of: 1
PPM setting of: 6, Score of: 1
PPM setting of: 63, Score of: 1
PPM setting of: 8, Score of: 1
PPM setting of: 9, Score of: 1
PPM setting of: -1, Score of: 2
PPM setting of: 3, Score of: 4
PPM setting of: 4, Score of: 4
PPM setting of: 5, Score of: 4
PPM setting of: 7, Score of: 4
PPM setting of: 2, Score of: 8
PPM setting of: 0, Score of: 51
PPM setting of: 1, Score of: 94

Estimated optimum PPM setting: 1

In this instance, the RTL-SDR has a PPM of 1, so we would set the environment variable READSB_RTLSDR_PPM=1.

Getting help

Please feel free to open an issue on the project's GitHub.

I also have a Discord channel, feel free to join and converse.

Changelog

See the project's commit history.