`nrf-softdevice`

Rust bindings for Nordic Semiconductor nRF series SoftDevices.

SoftDevices are a closed source C binary written by Nordic for their microcontrollers that sits at the bottom of flash and is called first on startup. The softdevice then calls your application or bootloader or whatever is sitting directly after it in flash.

They are full featured, battle tested, and pre qualified for bluetooth certification and thus make valuable bluetooth stacks when bindgened to Rust -- at least until we get a Rust bluetooth stack certified to be shipped commercially. Different SoftDevices support specific chips as well as certain features, like working only as a peripheral, or both a peripheral and central, or even offer alternate radio configuration like ant.

Besides the handicap of being closed source, the cost of SoftDevices is they steal away resources like ram and flash as well as timer peripherals and several priorities of interrupts from your application.

High-level bindings

The nrf-softdevice crate contains high-level easy-to-use Rust async/await bindings for the Softdevice.

Working:

Safe interrupt management
Async flash API
Bluetooth central (scanning and connecting)
Bluetooth peripheral (advertising, connectable-only for now)
GATT client
GATT server
L2CAP Connection-Oriented channels
Data length extension
ATT MTU extension
Get/set own BLE address

To use it you must specify the following Cargo features:

exactly one softdevice model, for example feature s140.
exactly one supported nRF chip model, for example feature nrf52840.

The following softdevices are supported.

S112 (peripheral only)
S113 (peripheral only)
S122 (central only)
S132 (central and peripheral)
S140 v7.x.x (central and peripheral)

The following nRF chips are supported

nRF52810
nRF52832
nRF52833
nRF52840

Some softdevices support only some chips, check Nordic's documentation for details.

Setting up your build environment

This project uses new toolchain features, often only to be found in nightly. Please ensure that your toolchains are up to date:

rustup update

You will also need probe-run - a utility to enable cargo run to run embedded applications on a device:

cargo install probe-run

Running examples

The following instructions are for the S140 and nRF52840-DK. You may have to adjust accordingly and can do so by modifying the cargo.toml of the examples folder - please check out the nrf-softdevice and nrf-softdevice-s140 dependency declarations.

Flashing the softdevice is required. It is NOT part of the built binary. You only need to do it once at the beginning, or after doing full chip erases.

Download SoftDevice S140 from Nordic's website here. Supported versions are 7.x.x
Unzip
As a debug client, if you are using
- probe-rs:
  - Erase the flash with probe-rs-cli erase --chip nrf52840
  - Flash the SoftDevice with probe-rs-cli download --chip nrf52840 --format hex s140_nrf52_7.X.X_softdevice.hex
- nrfjprog:
  - Flash the SoftDevice with nrfjprog --family NRF52 --chiperase --verify --program s140_nrf52_7.0.1_softdevice.hex

To run an example, simply use cargo run from the examples folder:

cd examples && cargo run --bin ble_bas_peripheral

Configuring a SoftDevice

The first thing to do is find out how much flash the SoftDevice you've chosen uses. Look in the release notes, or google for your SoftDevice version and "memory map". For an s132 v7.3 its listed as 0x26000, or in human readable numbers 152K (0x26000 in hex is 155648 in decimal / 1024 bytes = 152K)

Set the memory.x to move your applications flash start to after the SoftDevice size and subtract it from the total available size:

MEMORY
{
  /* NOTE 1 K = 1 KiBi = 1024 bytes */
  /* These values correspond to the NRF52832 with SoftDevices S132 7.3.0 */
  FLASH : ORIGIN = 0x00000000 + 152K, LENGTH = 512K - 152K
  RAM : ORIGIN = 0x20000000 + 44K, LENGTH = 64K - 44K
}

You can pick mostly anything for ram right now as if you have defmt logging enabled, the SoftDevice will tell you what the right number is when you call enable:

1 INFO  softdevice RAM: 41600 bytes
└─ nrf_softdevice::softdevice::{impl#0}::enable @ /home/jacob/.cargo/git/checkouts/nrf-softdevice-03ef4aef10e777e4/fa369be/nrf-softdevice/src/fmt.rs:138
2 ERROR panicked at 'too little RAM for softdevice. Change your app's RAM start address to 2000a280'

You have some control over that number by tweaking the SoftDevice configuration parameters. See especially the concurrent connection parameters. If you dont need to support multiple connections these can really decrease your ram size:

conn_gap.conn_count The number of concurrent connections the application can create with this configuration
periph_role_count Maximum number of connections concurrently acting as a peripheral
central_role_count Maximum number of connections concurrently acting as a central

Next you need to find out if your board has an external oscillator (which provides better battery life) But if in doubt just assume it doesn't and set the SoftDevice to use an internal clock. A common no external crystal configuration for nRF52 might be

        clock: Some(raw::nrf_clock_lf_cfg_t {
            source: raw::NRF_CLOCK_LF_SRC_RC as u8,
            rc_ctiv: 16,
            rc_temp_ctiv: 2,
            accuracy: raw::NRF_CLOCK_LF_ACCURACY_500_PPM as u8,
        }),

Interrupts

The SoftDevice does time-critical radio processing at high priorities. If its timing is disrupted, it will raise "assertion failed" errors. There's two common mistakes to avoid: (temporarily) disabling the softdevice's interrupts, and running your interrupts at too high priority.

These mistakes WILL cause "assertion failed" errors, 100% guaranteed. If you do these only "a little bit", such as disabling all interrupts but for very short periods of time only, things may appear to work, but you will get "assertion failed" errors after hours of running. Make sure to follow them to the letter.

The Softdevice Driver (e.g. Softdevice::run()) cannot be used from interrupts by default. However, the usable-from-interrupts feature enables this functionality. To use this feature, a critical-section implementation is required. This crate's internal implementation (critical-section-impl feature) is recommended, but other Softdevice-compatible implementations should also work.

Critical sections

Interrupts for certain peripherals and SWI/EGUs are reserved for the SoftDevice. Interrupt handlers for them are reserved by the softdevice, the handlers in your application won't be called.

DO NOT disable the softdevice's interrupts. You MUST NOT use the widely-used cortex_m::interrupt::free for "disable all interrupts" critical sections. Instead, use the critical-section crate, which allows custom critical-section implementations:

Make sure the critical-section-impl Cargo feature is enabled for nrf-softdevice. This makes nrf-softdevice emit a custom critical section implementation that disables only non-softdevice interrupts.
Use critical_section::with instead of cortex_m::interrupt::free. This uses the custom critical-section impl.
Use embassy_sync::blocking_mutex::CriticalSectionMutex instead of cortex_m::interrupt::Mutex.

Make sure you're not using any library that internally uses cortex_m::interrupt::free as well.

Interrupt priority

Interrupt priority levels 0, 1, and 4 are reserved for the SoftDevice. Make sure to not use them.

The default priority level for interrupts is 0, so for every single interrupt you enable, make sure to set the priority level explicitly. For example:

use embassy_nrf::interrupt::{self, InterruptExt};

let mut irq = interrupt::take!(SPIM3);
irq.set_priority(interrupt::Priority::P3);
let mut spim = spim::Spim::new( p.SPI3, irq, p.P0_13, p.P0_16, p.P0_15, config);

If you're using embassy-nrf with the gpiote or time-driver-rtc1 features enabled, you'll need to edit your embassy_config to move those priorities:

// 0 is Highest. Lower prio number can preempt higher prio number
// Softdevice has reserved priorities 0, 1 and 4
let mut config = embassy_nrf::config::Config::default();
config.gpiote_interrupt_priority = Priority::P2;
config.time_interrupt_priority = Priority::P2;
let peripherals = embassy_nrf::init(config);

Troubleshooting

If your SoftDevice is hardfaulting on enable and you think you have everything right, make sure to go back and do a full chip erase or recover, and reflash the SoftDevice again. A few bytes of empty space after the SoftDevice are required to be 0xFF, but might not be if the softdevice was flashed over an existing binary.

If the following linking error occurs

rust-lld: error: undefined symbol: _critical_section_release

make sure the feature critical-section-impl is enabled and also that the softdevice is included in the code, e.g. use nrf_softdevice as _;.

If running the firmware timeouts after flashing, make sure the size and location of the RAM and FLASH region in the linker script is correct.

Low-level raw bindings

The nrf-softdevice-s1xx crates contain low-level bindings, matching 1-1 with the softdevice C headers.

They are generated with bindgen, with extra post-processing to correctly generate the svc-based softdevice calls.

Generated code consists of inline functions using inline ASM, ensuring the lowest possible overhead. Most of the times you'll see them inlined as a single svc instruction in the calling function. Here is an example:

#[inline(always)]
pub unsafe fn sd_ble_gap_connect(
      p_peer_addr: *const ble_gap_addr_t,
      p_scan_params: *const ble_gap_scan_params_t,
      p_conn_params: *const ble_gap_conn_params_t,
      conn_cfg_tag: u8,
) -> u32 {
    let ret: u32;
    core::arch::asm!("svc 140",
        inout("r0") p_peer_addr => res,
        inout("r1") p_scan_params => _,
        inout("r2") p_conn_params => _,
        inout("r3") conn_cfg_tag => _,
        lateout("r12") _,
    );
    ret
}

Generating

The bindings are generated from the headers with the gen.sh script.

License

This repo includes the softdevice headers, which are licensed under Nordic's proprietary license. Generated binding.rs files are a derived work of the headers, so they are also subject to Nordic's license.

The high level bindings (nrf-softdevice) and the generator code (nrf-softdevice-gen) are licensed under either of

Apache License, Version 2.0 (LICENSE-APACHE or http://www.apache.org/licenses/LICENSE-2.0)
MIT license (LICENSE-MIT or http://opensource.org/licenses/MIT)

at your option.

embassy-rs/nrf-softdevice

embassy-rs

Reviews

Repository Details