STRF
strf is the satellite tracking toolkit for radio observations (RF). The software is designed to allow tracking of satellites from radio observations, using Doppler curves to identify satellites and/or determine their orbits.
The software is designed for linux operating systems, and will work with most software defined radios (SDRs), certainly those that are supported by http://www.gnuradio.org. The software comes with tools for data acquisition, performing FFTs to generate timestamped spectrograms (waterfall plots), and analysis, to extract and analyse Doppler curves.
Install
- For Ubuntu systems or similar.
- Install dependencies:
sudo apt install git make gcc pgplot5 gfortran libpng-dev libx11-dev libgsl-dev libfftw3-dev dos2unix - Clone repository:
git clone https://github.com/cbassa/strf.git - Compile:
cd strf; make - Install (in
/usr/local):sudo make install
- Install dependencies:
Configure
- You will need to set the following environment variables in your login file to run strf.
ST_DATADIRpath to strf directory (e.g.$HOME/software/strf, default: './')ST_TLEDIRpath to TLE directory (e.g.$HOME/tle)ST_COSPARCOSPAR site number (add to site location to$ST_DATADIR/data/sites.txt)ST_LOGINspace-track.org login info (of the formST_LOGIN="identity=username&password=password")ST_SITES_TXTpath to sites.txt (optional, default:$ST_DATADIR/data/sites.txt)
- Run
tleupdateto download latest TLEs. - You should install NTP support on the system and configure time/date to automatically synchronize to time servers.
Operation
The main use of strf is to acquire IQ data from SDRs and produce time stamped spectrograms with the rffft application. rffft will perform Fast Fourier Transforms on the input data to a user defined number of spectral channels (via the -c command line option), and integrate/average these to a user defined integration length (via the -t command line option). The output will be a *.bin file which contains a 256 byte human readable header (which can be inspected with head -c256), followed by a binary array of floating point numbers representing the power in the spectral channels. This is an example of the 256 byte header:
HEADER
UTC_START 2018-01-12T15:59:13.524
FREQ 2244000000.000000 Hz
BW 4000000.000000 Hz
LENGTH 0.998922 s
NCHAN 40000
NSUB 60
END
The header keywords are mostly self explanatory, though the NSUB keyword specifies that this single bin file contains 60 spectra.
rffft can read from a previously recorded IQ recording, but is usually operated in realtime mode by reading IQ data from a so-called named pipe or fifo (first in, first out). Here, the SDR writes IQ data to a fifo (instead of a file), and rffft reads the samples from the fifo. Using an airspy as an example, it could be configured as follows:
mkfifo fifo
rffft -i fifo -f 101e6 -s 2.5e6 &
airspy_rx -a 1 -f 101 -t 2 -r fifo
Here, we first make the fifo mkfifo fifo, then start rffft to read from the fifo (-i option), with a 101MHz center frequency (-f option) and a 2.5MHz sample rate (-s option). The & puts this command in the background. Finally, we start obtaining IQ data from the airspy with airspy_rx in the 2.5MHz sampling mode (-a 1) at the same frequency (-f 101, in MHz), with the 2.5MHz sample rate (-t 2) and writing the samples to the fifo (-r fifo). Similar scripts can be made with other SDRs, and otherwise with gnuradio flow graphs where the output file sink is a fifo.
Alternatively, when no input filename is given (with the -i option), rffft will read from stdin so it is possible to directly pipe an SDR receiver's application into rffft.
With an RTL-SDR:
rtl_sdr -g 29 -f 97400000 -s 2048000 - | ./rffft -f 97400000 -s 2048000 -F char
Here we use the RTL-SDR receiver with rtl_sdr with a gain of 29dB (-g 29), a center frequency of 97.4MHz (-f 97400000, in Hz) and a samplerate of 2.048MS/s (-s 2048000, in S/s). Note the trailing dash (-) in the rtl_sdr command to tell it to write to stdout instead of a file so it can be piped (|) through rffft. The same center frequency and samplerate are given to rffft. As rtl_sdr outputs data as 8 bits, -F char is required to tell rffft the format of the data.
With a HackRF:
hackrf_transfer -l 24 -g 32 -f 97400000 -s 8000000 -r - | ./rffft -f 97400000 -s 8000000 -F char -c 100
Here we use the HackRF receiver with hackrf_transfer with a lna gain of 24dB (-l 24), an IF gain of 32dB (-g 32), a center frequency of 97.4MHz (-f 97400000, in Hz) and a samplerate of 8MS/s (-s 8000000, in S/s). The output file is given as stdout (-r -). Again the same frequency and samplerate are given to rffft and as hackrf_transfer also outputs 8 bit data -F char is also required for rffft.
With a Adalm Pluto:
iio_attr -u usb:x.y.z -c ad9361-phy RX_LO frequency 97400000
iio_attr -u usb:x.y.z -c ad9361-phy voltage0 rf_port_select A_BALANCED
iio_attr -u usb:x.y.z -c ad9361-phy voltage0 rf_bandwidth 2000000
iio_attr -u usb:x.y.z -c ad9361-phy voltage0 sampling_frequency 2000000
iio_attr -u usb:x.y.z -c ad9361-phy voltage0 gain_control_mode manual
iio_attr -u usb:x.y.z -c ad9361-phy voltage0 hardwaregain 60
iio_readdev -u usb:x.y.z -b 4194304 cf-ad9361-lpc | ./rffft -f 97400000 -s 2000000 -F int
Here we use the Adalm Pluto transceiver with iio_readdev. The transceiver is connected via USB. Replace x.y.z by the USB bus ID of your transceiver. You can retreive the USB IDs from the output of iio_info -s. Connection via Ethernet is possible as well. Before receiving we have to set center frequency, samplerate, gain, ... by a bunch of iio_attr commands.
With I/Q recordings obtained from Gqrx:
./rffft -i gqrx_YYYYMMDD_HHMMSS_97400000_2000000_fc.raw -f 97400000 -s 2000000 -F float -T "YYYY-MM-DDTHH:MM:SS"
Gqrx records complex samples into raw files. The filename contains date, time, center frequency and samplerate separated by underscores. Replace YYYYMMDD and HHMMSS by your actual time and respectively. Pay attention to insert an uppercase T between date and time in the time stamp parameter of the rffft command.
The output spectrograms can be viewed and analysed using rfplot.