avandalen/Spotwelder-controller

Stars
11
Rank 1,694,829 (Top 34 %)
Language
C++
Created over 4 years ago
Updated over 4 years ago

avandalen/Spotwelder-controller

avandalen

There are no reviews yet. Be the first to send feedback to the community and the maintainers!

avdweb_Switch

Switch library with longPress and doubleClick

avdweb_AnalogReadFast

VirtualDelay

Non-blocking Virtual Delay timer. Timer-rollover safe. For the Arduino Uno and Zero.

avdweb_FreqPeriodCounter

Smart library with comprehensive functions for counting (multiple) frequencies and period-times. For Arduino Uno and Zero.

SAM-15x15

avdweb_SAMDtimer

SAMD21 Timer library for the SAM15x15 and Arduino Zero

PCB-Spotwelder-Controller

avdweb_scope

Debug oscilloscope library for the Arduino

Eagle-library-addressable-LED-rings

Eagle library for easily create addressable LED rings NeoPixel WS2812B-2020

SAM15x15

SAM15x15 board / Arduino Zero package which describes all SAMD21G pins

MAX17263-Arduino-library

avdweb_pedelec_legalisation_device

Spotwelder

avdweb_DAC16

Cheap 16 bit DAC AD5662 for the Arduino

Fast-PWM-DAC-for-the-Arduino

Create a faster DAC than analogWrite() with the FastPWMdac library

avdweb_SAMDpwmDAC

Fast PWM-DAC library for the SAM15x15 and Arduino Zero

Simulation-e-bike-hub-and-mid-drive-motor-efficiency-vs-speed

Here we can simulate an e-bike with a hub motor or mid-drive motor in all situations. Also, a mid-drive motor can be tested at a constant cadence / bottom bracket speed.

LTC2944-library-Battery-Gas-Gauge

Connectorless-zigzag-1x6-mini-ISP-connector

An Arduino ISP connector is used, among others, for burning a bootloader and for programming ATtiny chips. When the ISP connector is only used once, it would be more convenient not to use a connector. Therefore, I created the connectorless 1x6 mini ISP connector and the mini 1x6 ISP adapter. By the zigzag positions of the PCB holes, the male ISP connector pins press against the holes and make electrical contact and so, no PCB connector is needed.

Albert-Arduino-library

Changing-Arduino-IDE-theme-colors

Changing the Arduino IDE tab and comment font colors

MH-M38-Bluetooth-audio-receiver-schematic

One-Button-Menu

This menu creates an intuitive and efficient way to browse and set options with just one button and one LED, as opposed to conventional menu interfaces that use an LCD display with multiple buttons.ne LED, as opposed to conventional menu interfaces that use an LCD display with multiple buttons.

LTC2499-LTC2493-24bit-ADC

This library can be used for: LTC2493: 2/4 channel 24bit ADC LTC2499: 8/16 channel 24bit ADC This library contains the ADC part of the combined library Ard2499 which contains the libraries for the LTC2499 24bit ADC and the 24AA025E48 EEPROM See the 16-Channel 24-Bit ADC Data Acquisition Shield for Arduino from Iowa Scaled Engineering: * https://www.iascaled.com/store/Arduino/ArduinoDataAcquisition/ARD- * GitHub https://github.com/IowaScaledEngineering/ard-ltc2499

Rain-sensor-for-Somfy-motorized-awning

Solarcell-curve-tracer

ILI9341-overwrite-text

The Adafruit_ILI9341 library cannot print new text over other text correctly. The old text is not erased first as it should. With this library extension we can overwrite text and numbers correctly.

Daytime-running-light-for-ebikes

avdweb_HeartBeat

FDTI-UPDI-connector

Typically, debugging via the serial monitor and burning the bootloader requires 2 connectors: FTDI For debugging and uploading the sketch UPDI For burning the boot loader (like the ICSP connector for the Atmega328 and others) These connectors, however, take up a lot of space on the pcb, especially with respect to the fact that the ATtiny devices, such as the ATtiny3217, are very small. That is why I have designed a new combined FTDI / UPDI connector, which take less space on the pcb.