UedaTakeyuki/mh-z19 UedaTakeyuki/mh-z19

  • Stars
    star
    173
  • Rank 220,124 (Top 5 %)
  • Language
    Python
  • License
    MIT License
  • Created about 6 years ago
  • Updated 12 months ago
Twitter logo Share LinkedIn logo Share Facebook logo Share
UedaTakeyuki/mh-z19
github

UedaTakeyuki

Reviews

There are no reviews yet. Be the first to send feedback to the community and the maintainers!

Repository Details

Read CO2 concentration from mh-z19 sensor on the Raspberry Pi & handle it. Detect Raspberry Pi model automatically and read the value from an appropriate serial device.

mh-z19

Read CO2 concentration from mh-z19 sensor and handle it.

MH-Z19

cabling

Connect RPi & mh-z19 as:

  • 5V on RPi and Vin on mh-z19
  • GND(0v) on RPi and GND on mh-z19
  • TxD and RxD are connected to cross between RPi and mh-z18

Followings are example of cabling, but you can free to use other 5v and 0v Pin on the RPi.

Cabling

pi@raspberrypi:~/mh-z19 $ gpio readall
 +-----+-----+---------+------+---+---Pi B+--+---+------+---------+-----+-----+
 | BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
 +-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
 |     |     |    3.3v |      |   |  1 || 2  |   |      | 5v      |     |     |
 |   2 |   8 |   SDA.1 |   IN | 1 |  3 || 4  |   |      | 5v      |     |     |  <---- Vin
 |   3 |   9 |   SCL.1 |   IN | 1 |  5 || 6  |   |      | 0v      |     |     |  <---- Gnd
 |   4 |   7 | GPIO. 7 |   IN | 1 |  7 || 8  | 1 | ALT0 | TxD     | 15  | 14  |  <---- RxD
 |     |     |      0v |      |   |  9 || 10 | 1 | ALT0 | RxD     | 16  | 15  |  <---- TxD
 |  17 |   0 | GPIO. 0 |   IN | 0 | 11 || 12 | 0 | IN   | GPIO. 1 | 1   | 18  |
 |  27 |   2 | GPIO. 2 |   IN | 0 | 13 || 14 |   |      | 0v      |     |     |
 |  22 |   3 | GPIO. 3 |   IN | 0 | 15 || 16 | 0 | IN   | GPIO. 4 | 4   | 23  |
 |     |     |    3.3v |      |   | 17 || 18 | 0 | IN   | GPIO. 5 | 5   | 24  |
 |  10 |  12 |    MOSI |   IN | 0 | 19 || 20 |   |      | 0v      |     |     |
 |   9 |  13 |    MISO |   IN | 0 | 21 || 22 | 0 | IN   | GPIO. 6 | 6   | 25  |
 |  11 |  14 |    SCLK |   IN | 0 | 23 || 24 | 1 | IN   | CE0     | 10  | 8   |
 |     |     |      0v |      |   | 25 || 26 | 1 | IN   | CE1     | 11  | 7   |
 |   0 |  30 |   SDA.0 |   IN | 1 | 27 || 28 | 1 | IN   | SCL.0   | 31  | 1   |
 |   5 |  21 | GPIO.21 |   IN | 1 | 29 || 30 |   |      | 0v      |     |     |
 |   6 |  22 | GPIO.22 |   IN | 1 | 31 || 32 | 0 | IN   | GPIO.26 | 26  | 12  |
 |  13 |  23 | GPIO.23 |   IN | 0 | 33 || 34 |   |      | 0v      |     |     |
 |  19 |  24 | GPIO.24 |   IN | 0 | 35 || 36 | 0 | IN   | GPIO.27 | 27  | 16  |
 |  26 |  25 | GPIO.25 |   IN | 0 | 37 || 38 | 0 | IN   | GPIO.28 | 28  | 20  |
 |     |     |      0v |      |   | 39 || 40 | 0 | IN   | GPIO.29 | 29  | 21  |
 +-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
 | BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
 +-----+-----+---------+------+---+---Pi B+--+---+------+---------+-----+-----+

Install & Setup

Full Set Install

Full Set include followings:

  • Setup script: Install & Setup following useful stuffs as:
    • mh-z19: A python module to read mh-z19 sensor.
    • PondSlider: A multipurpose versatile sensor handler for python, which read mh-z19 value and handle it.
    • autostart.sh: Utility making mh-z19 as system service to act periodically.

Install Full Set, download from release

git clone https://github.com/UedaTakeyuki/mh-z19.git

Then, got to the folder and issue setup.sh*

./setup.sh

Necessary settings including serial port enabling are taken place in this script.

Install only sensor module

For python 2.x

sudo pip install mh_z19

For python 3.x

sudo pip3 install mh_z19

In case you would use it witout root permission, call pip without sudo as follows:

For python 2.x

pip install mh_z19

For python 3.x

pip3 install mh_z19

The differences of the interface between each Raspberry Pi model are resolved inside this module. For example, serial device name is difference between Raspberry Pi 3 and older model, but mh-z19 module automatically detect the model and read from appropriate serial device.

To use mh-z19, once you need to set up enabling serial port device on the Raspberry Pi. Following Wiki page might be informative. Also, please refer PyPi top page for detail.

read CO2 Sensor value

pi@raspberrypi:~ $ sudo python -m mh_z19 
{'co2': 668}

As above, sudo might be necessary because mh-z19 sensor value is read through serial connection and it request root permission in general.

Handle sensor value by PondSlider multipurpose sensor handler.

The installed mh-z19 module is correspond the pondslider which is multiple & versatile sensor handler to save, send and to do other necessary something with the sensor value.

As an example, we introduce following use case:

  • How to save sensor value to SD card as .CSV file.
  • How to send sensor value to free Remote Monitoring Service.

A brief explanation of pondslider

The pondslider read sensorvalue by sensor-handler specified, and pass the values to value-handlers* which do something with it.

PondSlider

Both sensor and value handlers are python module. For more detail of handlers, please refer this.

How to use sensor value to send to server, save to strage, and so on.

This module correspond the pondslider which is multiple & versatile sensor handler to save, send and to do other necessary something with the sensor value.

In case you choiced Full Install mentioned above, in other words, you've done setup.sh, the pondslider and there example handler's are already installed & setup.

How to save CO2 value on a SD card as a .CSV file.

You can do it with save2strage value handler which is in handlers/value/saver/save2strage, and configuration file to read from mh-z19 sensor and save by save2strage is prepared as config.save.toml on the mh-z19 installed folder.

On the mh-z19 folder By calling pondslider as follows;

sudo python -m pondslider --config config.save.toml

Then, /home/pi/DATA/co2.csv should be created and new line will be added for each call.

How to send CO2 Value to the MONITOR™ Service

The MONITOR™ is a free Remote Monitoring Service to show latest data on the web.

Please refer an introduction to grasp birds-eye understanding about MONIOR™.

A free account is available as follow. Then, login and get a view_id, which is unique id to point a data area on the MONITOR™ to show latest value and chart, as follow.

After get a value_id at your browser, return back to terminal of your Raspberry Pi, then you should set your this software to send measured value to the value_id. To do this, call setid.sh command in the mh_z19 installed directory. Let's say your value_id is vpgpargj, issue setid.sh command as follows:

./setid.sh vpgpargj

Then, call "pondslider" python script as follows:

pi@raspberrypi:~/mh-z19 $ sudo python -m pondslider
{'co2': 742}
co2
{"ok":false,"reason":"ViewID not valid"}

Your time-series chart on the MONITOR™ display on the browser must be updated by the latest CO2 concentration value.

How to set your Raspberry Pi to send CO2 data to MONITOR™ at 5 minute interval.

You can set it by autostart.sh command in the mh_z19 installed directory as follows:

./autostart.sh --on

You can turn off this as follows:

./autostart.sh --off

Also, You can check current status as follows:

./autostart.sh --status

For more detail, please refer this blog.

How to send CO2 Value to the ATT M2X.

The Pondslider also support ATT M2X. For detail, please refer this document.

Calibration, Detection range settings, and ABC(Automatic Baseline Correction) logic on/off.

Features about calibration (both MH-Z19 & MH-Z19B), detection range change (MH-Z19B) and ABC logic on/off(MH-Z19B) are implemented at version 0.2.1 or later.

I'm afraid I've just only implemented these without test due to lack necessary devices and apparatus for the test, fx: standard concentration CO2 GAS, also MH-Z19B module. If you have these devices or apparatus and try to use these functions generously, I really appreciate your issue report regardless result were positive or negative.

For detail please refer this wiki.

Undocumented response values of 0x86 command.

The Revspace/MHZ19 shows values undocumented on the official datasheets (MH-Z19, MH-Z19B). In accordance with this, --all option add these values in the return json value as follows:

sudo python -m mh_z19 --all
{"SS": 232, "UhUl": 10752, "TT": 61, "co2": 818, "temperature": 21}

sudo python3 -m mh_z19 --all
{"TT": 61, "co2": 807, "SS": 232, "temperature": 21, "UhUl": 10752}

or call read_all() function as follows:

>>> import mh_z19
>>> mh_z19.read_all()
{'SS': 232, 'UhUl': 10738, 'TT': 61, 'co2': 734, 'temperature': 21}
>>>

Use specific serial device.

In case you should use specific serial device instead of Raspberry Pi default serial device which this library automatically select, for example in case to need to use /dev/ttyUSB0 for FT232 usb-serial converter as issue#12, you can specify serial device by --serial_device option as follows:

sudo python -m mh_z19 --serial_device /dev/ttyUSB0

How to use without root permission.

See this wiki.

How to use in your program.

See this wiki.

PWM support.

See this wiki.

In case you can't get the value.

Even if cabling seems no problem and uart seems to be prepateted well but you can't get sensor value. As nincube8 suggested that the pull up by 1-5kΩ register can be working solution. Thank you nincube8!

Q&A

The forum is avai at here. Any questions, suggestions, reports are welcome!

Blog

References

history

More Repositories

1

pondslider

Versatile sensor handler that can handle different sensors in the same way.
Python
5
star
2

slider

A simple data collector.
Python
4
star
3

Backup-Pi

Backing up and Restoring your Raspberry Pi's SD Card using Raspberry Pi.
PHP
3
star
4

monitor2_leaflet

manuscript of monitor2 leaflet
2
star
5

slider_lesson_text

IoT の基礎を学ぶための実践例題集
Makefile
1
star
6

piserialnumber

Get Raspberry Pi board serialnumbermodel number
Python
1
star
7

getrpimodel

Get Raspberry Pi model Name(eg: A, B, B+...)
Python
1
star
8

incremental_counter

Persistent Incremental Counter
Python
1
star
9

barcodelogger

barcodelogger: read barcode by iOS or Android, log on the server, download as Excel.
PHP
1
star
10

gc_modem

USB 3G dongle utils
Python
1
star
11

rhizosphere

root server for collaborative devices
Python
1
star
12

GetRPimodel_cpp

C++ Header only library to get Raspberry Pi model Name(eg: A, B, B+...) and secondary informations provided a table https://elinux.org/RPi_HardwareHistory.
C++
1
star
13

sansi_examples

sample projects of how to protect your application against unauthorized copying, with the sansi library.
C
1
star