ESP32 CSI Tool
The purpose of this project is to allow for the collection of Channel State Information (CSI) from the ESP32 Wi-Fi enabled microcontroller. By collecting this data rich signal source, we can use this information for tasks such as Wi-Fi Sensing and Device-free Localization directly from the small, self contained ESP32 microcontroller.
The following projects can be found in this repository:
./active_sta- Active CSI collection (Station) - Connects to some Access Point (AP) (Router or another ESP32) and sends packet requests. (Typically used as CSI-TX)./active_ap- Active CSI collection (AP) - AP which can be connected to by devices (ESP32, see previous). (Typically used as CSI-RX)./passive- Passive CSI collection - Passively listens for CSI frames on a given channel (default: channel 3).
Each project automatically sends the collected CSI data to both serial port and SD card (if present). These settings can be configured as described below.
In addition to these ESP32 specific projects, we also consider methods for analyzing CSI in Python and MATLAB (See Analysing CSI Data below).
Installation
First, Install Espressif IoT Development Framework (ESP-IDF) by following their step by step installation guide. Notice, this project requires version (v4.3) of ESP-IDF.
Important: It is important that you are able to successfully build and flash the example project from the esp-idf guide onto your own esp32. If you have issues building the example project on your hardware, do not create an issue in this github repo. We will not be able to assist with general ESP32 issues (those issues that are unrelated to this project).
Next, clone this repository:
git clone https://github.com/StevenMHernandez/esp32-csi-tool
Finally, decide which sub-project you would like to flash to your ESP32(s). The simplest case would be to use two ESP32s. One using the Active CSI collection (Station) codebase and the other using the Active CSI collection (AP) codebase. To begin working with a given codebase, open a terminal and change into the respective directory.
cd ./active_sta # For Active Station (Typically used as the CSI-TX)
# OR
cd ./active_ap # For Active Access Point (Typically used as the CSI-RX)
# OR
cd ./passive # For Passive CSI collection (Used as a passive-RX)
We can now begin configuring and flashing your ESP32.
Configuration (ESP-IDF)
The ESP-IDF provides great control over project configuration. This configuration can be updated by running the following command from your terminal.
idf.py menuconfig
It is important to notice that these configurations are project specific and will not automatically be copied between sub-projects. So for example, make sure when you change the Wi-Fi password in Active CSI collection (AP), you also update this configuration in the Active CSI collection (Station) project as well.
The following configurations are important for this project:
Serial flasher config > 'idf.py monitor' baud rate > Custom Baud RateSerial flasher config > Custom baud rate value > 921600This allows more data to be transmitted on the Serial portComponent config > Common ESP32-related > Channel for console output > Custom UARTComponent config > Common ESP32-related > UART console baud rate > 921600Component config > Wi-Fi > WiFi CSI(Channel State Information)(Press space to select)Component config > FreeRTOS > Tick rate (Hz) > 1000ESP32 CSI Tool Config > ****all options in this menu can be specified per your experiment requirements.
NOTE: For some systems, other baud rates may be required. Good options to try are 921600, 1000000, 1152000, 1500000, and 1552000.
The higher baud rate the better! Baud rate is extremely important to achieve high sampling rates without lag!
If you have a problem, please leave any relevant information such as operating system, esp-idf version, list of all baud rates work and baud rates that do not work etc in issue #5.
Flash ESP32
Run the following command from within one of the sub-project's directories.
idf.py flash monitor
This will flash the ESP32 and once completed, will print incoming data from the freshly programmed ESP32's serial port.
To exit monitoring, use ctrl+]
Collecting CSI Data
There are two methods to collect CSI data. If your ESP32 has an SD card on board (such as the TTGO T8 V1.7 ESP32), the ESP32 will automatically detect the SD card and automatically output CSI data to a simple csv file.
If the device does not have an SD card or you wish to collect the data directly from the Serial port on your computer, you can run the following command:
# macOS or Linux
idf.py monitor | grep "CSI_DATA" > my-experiment-file.csv
# Windows
idf.py monitor | findstr "CSI_DATA" > my-experiment-file.csv
Because the clocks on the ESP32 are not synchronized with any real world time, it can be difficult to sync this data with other external data sources or sensors. To help with this, we can pass output first through a python script which appends a timestamp from your computer.
idf.py monitor | python ../python_utils/serial_append_time.py > my-experiment-file.csv
Analysing CSI Data
Once data has been collected, we now wish to run analysis and (most likely) apply deep learning algorithms on the collected data. Luckily, the output from the esp32 is a simple CSV file, thus we can pass the contents to any available CSV parser in our language of choice (Python, MATLAB, R, etc.). The use of CSV was selected for its simplicity and small size when compared with the likes of XML or JSON.
Visualizing CSI Data
If you wish to visualize the incoming CSI amplitude data in real-time, use the ./python_utils/serial_plot_csi_live.py script.
First, install the python plotting dependencies.
pip install numpy matplotlib
Then, to visualize the CSI amplitude, use the following command.
idf.py monitor | python ../python_utils/serial_plot_csi_live.py
Currently this script only visualizes subcarrier #44. You can change this by editing the code directly.
Advanced:
Setting Local Time
Because the ESP32 is not connected to the internet as a whole, it is not possible to automatically set the clock time locally. To handle this, we offer the ability to set the time in a couple of different ways.
First, while running idf.py monitor we can type the following SETTIME: 123123123123 then ENTER where the number 123123123123 indicates the current UNIX time in seconds.
Additionally, the access point code in ./active_ap will automatically send its current timestamp to any connected station running the ./active_sta sub-project.
This means that you only need to set the time for the access point and all other nodes will synchronize automatically.
Finally, the simplest method is to simply run the output of idf.py monitor through a utility function which appends the correct timestamp to the output when received on your computer as described in the *Collecting CSI Data section above.
Misc.
ESP32 CSI Tool developed by Steven M. Hernandez