Stratum-1 GNSS Time Server Built From Scratch-GNSSTimeServer

Answer the survey: Crowdfunding for GNSS Time Server

Ethernet/WiFi enabled, GNSS fed, NTP/RDATE server based on ESP8266/ESP32 and Arduino

🎖️ Featured by Hackaday

🎖️ Selected for Maker Faire Rome 2023

Maker Faire Rome 2023 pictures below:

Functionalities:

Internal real-time clock (RTC) with an integrated temperature-compensated crystal oscillator (TCXO), synched from Global Navigation Satellite System (GNSS) satellites constellation (GPS, BeiDou, GLONASS and Galileo; backed by CR2032 battery)
Real-time operating system (RTOS) multi-tasking (when used with ESP32); core tasks (GNSS synching, Clock updating, processing NTP/RFC868 requests) running with a higher priority than common tasks (display update, PPS led blinking, web page serving)
Rich dashboard with information about MCU, RTC, GNSS, WiFi (uptime, free heap, minimum heap, temperature, version, ip, mac address, network name, network type, signal strength, timestamp lat, long, lock status, sats, precision, etc)
Highly optimized web page (minimalist single HTML with no external dependency, embedded graphics (as base64 encoded strings, including favicon), embedded script and layout, gzip-compressed - Python conversion/compression script supplied), requiring a password for critical functions. Only 32 Kb in size total, further reduced to ~20Kb through GZip compression. All modern browsers support gzipped pages, the compression takes place before firmware compiling, so no computing cycle is wasted by the device
- Data separated from layout, once the page is loaded, data will be updated every 5 seconds from a lightweight JSON string, no full page reloads are needed
Over-The-Air (OTA) Web Based firmware upgrade
Dual voltage powered
Backup battery for the whole unit (18650)
NTP and RDATE (RFC868) protocols supported
WiFi functionality as a client or access point
10/100 Mbps Ethernet support (W5500 hardwired TCP/IP embedded Ethernet controller)
Syslog logging
Configuration webpage for WiFi and Syslog, saving to persistent storage (LittleFS)
Informative display with a timestamp, satellites in view, accuracy, WiFi server, IP address
Dual function button, short press switch information on display, long press disables WiFi
Status at a glance, with dedicated 5mm LEDs for GPS lock, PPS signal, and WiFi status, as well as visible internal leds for charging and GPS module statuses
- Yellow led will be on or off to indicate respective WiFi status
- Green led will blink/pulsate at different rates to indicate a lock is being acquired and stay steady green when locked
- Red led will blink once a second once lock is acquired, in sync with the PPS signal
Diagnostics messages on boot
- When turned on, the OLED will first display the reason for the last shutdown (if it was rebooted by the MCU itself due to a power oscillation or other reason or if it was a user-triggered shutdown) and proceed displaying the startup status of each module, so if it get stuck on boot you can know which module is hanging and troubleshoot faster.

Note

Please note that some functionalities are available only on ESP32, due to either ESP8266 limitation or the functionality not being backported yet.

Parts list:

Amica NodeMCU (ESP8266 / ESP-12) or ESP32Duino (ESP32-WROOM-32)
DS3231 RTC
GNSS module. Tested with:
- Neo-6m V2
- ATGM336H
- ZKMICRO AT6558D
- TOPGNSS Allystar TAU1201
1.3" SH1106 OLED Display
For mains powered:
- Hi-Link 5V/3W
- Mini-360 DC-DC Buck converter
- TP4056 Module
- 18650 battery holder
- 0.5A/230v fuse
- 10D561K varistor
For power adapter powered:
- 18650 battery shield
- 5.5mm x 2.1 mm or any other suitable socket
For the ethernet-enabled version:
- WIZNet W5500 module
Resistors (150, 100, and 150 Ohms respectively for above LEDs)
Switch key and momentary push button

New dashboard screenshot:

And the new 3D printable case:

Check also the Dual Display PIR Enabled branch option: https://github.com/Montecri/GPSTimeServer/tree/Dual-Display

ATTENTION

Several DS3231 modules being sold today contain a hazardous design flaw in which it supplies a voltage to the battery cradle regardless if it came with a rechargeable battery or not. If it came with a CR2032 battery (non-rechargeable) the consequence is that it will swell, explode, or worse. If it came with a LIR2032 battery (rechargeable), the module is fed with 5v will generate an unsafe charging voltage for that battery.

There are workarounds for that so you don't need to toss your module away, the most popular being removing a diode and/or resistor.

There's a long discussion on the thread below about the root cause and possible fixes:

https://forum.arduino.cc/t/zs-042-ds3231-rtc-module/268862/33

Libraries: